Mic Test – Check Your Microphone Online

See your input level live, pick the right microphone and hear a 5-second recording. Everything stays in your browser.

Your browser will ask for permission. Nothing is uploaded.

Press Start mic test and say something.

CLIP
–Level (RMS, dBFS)
–Peak hold (dBFS)
Signal
Browser processing (re-opens the mic)
Track settings reported by the browser
Device
–
Sample rate
–
Channels
–
Echo cancellation
–
Noise suppression
–
Auto gain
–

Record and play back 5 seconds

Use headphones, or turn your speaker volume down, before playing the recording back. Otherwise the microphone can pick up the speakers and cause a loud feedback howl.

Start the mic test first.

How to test your microphone

  1. Press Start mic test and allow access. The bar moves as soon as the browser hears anything.
  2. Talk at your normal volume from where you usually sit. The status line turns green when real sound arrives, and warns you about silence or clipping.
  3. If you own several microphones, choose each one from the list. The browser shows names only after you grant permission, which is why the list is empty at first.
  4. Press Record 5 seconds, then play it back to hear what other people hear. Headphones avoid feedback.

How to read the dBFS level

dBFS means decibels relative to full scale. 0 dBFS is the loudest value a digital signal can hold, so every reading is negative, and each 6 dB step roughly halves or doubles the signal. The bar shows the RMS (average) level, the thin marker holds the recent peak, and CLIP lights when samples reach full scale, which sounds like crackling distortion.

  • Below −60: effectively silence, often a muted or wrong device.
  • −55 to −42: room noise, or a voice that is too far away or too quiet.
  • About −30 to −15: typical for clear speech, with peaks a few dB higher.
  • Above −6, or CLIP: too loud. Lower the input level.

With auto gain on, the browser boosts a quiet voice, so the meter looks healthier than the raw microphone. Untick it to see the real input level.

Browser input versus system input

The browser picks its microphone separately from your system default. Chrome and Edge list a Default entry that follows the system, and on Windows also Communications. If this page hears you but a website does not, check which device that site chose. The hardware input level is set by the system (Windows: Settings → System → Sound → Input; macOS: System Settings → Sound → Input), not by the browser.

Bluetooth headset quirks

Bluetooth headphones play music over A2DP, a high-quality stereo profile with no microphone. When any app opens the headset mic, it switches to the hands-free profile (HFP), which carries narrowband mono in both directions. Music then sounds like a phone line until the mic is released. If quality matters, record with a wired or USB microphone, or the laptop's built-in one, and keep the headset for listening only.

Tips for Zoom, Teams and Discord

  • Press Stop or close this tab before joining a call. Some drivers let only one app use the microphone at a time.
  • Each app has its own microphone setting: Zoom under Settings → Audio, Teams under Settings → Devices, Discord under User Settings → Voice & Video. Choose the device that worked here.
  • These apps add their own noise suppression. If your voice sounds watery or cuts off at the start of words, lower that setting first.
  • If Discord's voice activity misses your words, raise the system input level until your speech sits around −30 to −15 here.

Setting up for a call or a stream? Check your camera with the webcam test, and your controls with the keyboard tester or gamepad tester.

Frequently asked questions

Is my voice recorded or uploaded?
No. The level meter only reads the sound in your browser and stores nothing. The 5-second recording is made only when you press Record, is kept in this tab's memory, and disappears when you close or leave the page. Nothing is sent to a server.
Why does it say "No sound detected" when my microphone is plugged in?
The browser opened a device but receives silence. Common causes: a mute switch on the headset or its cable, a muted input in the system sound settings, the wrong device selected in the list, or a privacy toggle (Windows: Settings → Privacy & security → Microphone). Try each device in the list while speaking.
The browser no longer asks for permission. How do I allow the microphone again?
Once you press Block, the browser remembers it and fails at once without asking. Click the icon to the left of the address bar, set Microphone to Allow and reload. The error message on this page shows the exact steps for your browser and system.
Should echo cancellation and noise suppression be on?
For calls on speakers, yes: they stop the other person hearing themselves and remove fan or keyboard noise. For recording music or a podcast, turn them off along with auto gain, because they change the tone and pump the volume. Try both here and compare the recordings.
Why does my Bluetooth headset sound worse as soon as I start the test?
Using the headset microphone switches most Bluetooth headsets from the stereo music profile (A2DP) to the hands-free profile (HFP), which has much lower audio quality. Press Stop and the sound returns to normal after a moment.
Does the mic test work on phones?
Yes, in current Safari on iPhone and iPad and in Chrome or Firefox on Android. Safari records in MP4 (AAC) instead of WebM, which this page handles automatically. In-app browsers inside social media apps often block the microphone, so open the page in your normal browser.